|
|
|
|
Jubal
May 31, 2012, 5:17 PM
Post #1 of 10
(2142 views)
Shortcut
Registered: Dec 26, 2009
Posts: 29
|
|
Inspecting your canopy
|
Can't Post
|
|
I've been thinking lately that my casual inspection of my base canopy before jumps is not focused enough and falls into the realm of complacency. For you rigger types out there, what should we be looking for on our inspections? I know what I look for, but a checklist would be nice. I did a forums search under canopy inspection and got nada. If this has already been covered I apologize. Antennae keep blinking their pretty come hither eyes at me...
|
|
|
|
|
Jubal
Jun 1, 2012, 1:19 AM
Post #3 of 10
(2002 views)
Shortcut
Registered: Dec 26, 2009
Posts: 29
|
|
Re: [waltappel] Inspecting your canopy
[In reply to]
|
Can't Post
|
|
I did. And that's how he spotted a tear in my center cell rib, about four feet back which I would not have spotted. I've looked into the cells, but to find this tear, you'd have to crawl up into the cell. So it got me to wondering how often I should inspect more than just the pc, lines, grommets, closing loop, seams, and outer fabric. Seemed like a good idea for a thread.
|
|
|
|
|
hjumper33
Jun 1, 2012, 4:01 AM
Post #4 of 10
(1953 views)
Shortcut
Registered: Jul 24, 2005
Posts: 525
|
|
Re: [Jubal] Inspecting your canopy
[In reply to]
|
Can't Post
|
|
I probably do a pretty decent inspection every 50 jumps or so with normal use, but if Ive landed anywhere weird or suspect damage, obviously moreso. The nice thing is the majority of base canopies are nicely overbuilt to take some abuse.
|
|
|
|
|
GreenMachine
Jun 1, 2012, 6:13 AM
Post #5 of 10
(1901 views)
Shortcut
Registered: Jan 24, 2003
Posts: 3468
|
....but I play one in my loft.
Same as hjumper33, I only fully inspect a
canopy when it is brand new, new to me, after
some funky situation, or when bored and have
time to kill. Here are some of the ways I use:
-Walk each line group seperately
-Lay it out and look at the top skin
-Lay it out and look at the bottom skin
-Climb inside every other cell and look
At Skydive Atlanta they have a long PVC pole
with clamps attached to it and suspended from
the 30ish foot ceiling with ropes. Any time I'm
there and have a BASE canopy unpacked I will
hang her up do a quick inspection also helps to
get the wrinkles out too.
I can and have hung up canopies in my loft aka
garage but it requires use of a ladder, hence I
only do it when necessary.
|
|
|
|
|
gauleyguide
Jun 1, 2012, 8:00 AM
Post #7 of 10
(1853 views)
Shortcut
Registered: May 2, 2006
Posts: 1244
|
|
Re: [Jubal] Inspecting your canopy
[In reply to]
|
Can't Post
|
|
If you really want to get into the inspection, I was shown once to use a small flashlight to look over every seam and stitch. The flashlight doesn't help you see better rather it helps your eyes focus on that spot and it keeps your eyes from wondering off from the part you are inspecting.
|
|
|
|
|
johnfulk
Jun 1, 2012, 10:56 AM
Post #8 of 10
(1779 views)
Shortcut
Registered: Nov 24, 2000
Posts: 56
|
|
Re: [gauleyguide] Inspecting your canopy
[In reply to]
|
Can't Post
|
|
I just take a look up at the canopy it when dayblazing. The sun will identify the holes. inspection complete.
|
|
|
|
|
-rm
Jun 1, 2012, 2:09 PM
Post #9 of 10
(1702 views)
Shortcut
Registered: May 19, 2011
Posts: 90
|
|
Re: [johnfulk] Inspecting your canopy
[In reply to]
|
Can't Post
|
|
Why else would you be doing CReW?
|
|
|
|
|
Lucifer
Jun 2, 2012, 3:06 AM
Post #10 of 10
(1596 views)
Shortcut
Registered: Feb 12, 2004
Posts: 61
|
|
Re: [Jubal] Inspecting your canopy
[In reply to]
|
Can't Post
|
|
Heres a quick review of all important points to check on a canopy to guarantee it's reliability.
Please note that an experienced rigger can certainly shortcut some steps and tell you to jump it or burn it because he can determine the state of the material visually and/or by just touching it with a very decent precision.
A.General state (throw away / continue)
B.Canopy:
1.stitchings, general (if many defects, change the canopy coz it's not worth fixing it)
2.leading edge reinforcements (webbing state / stitching / cells junction)
3.trailing edge (idem)
4.attachement points (pull and watch!)
5.fabric assembly (pull two cells apart and check how its spreading apart at junction/stitching line
6.inside reinforcements / ribs state (try to spot big damage or deformation on fabric around rib holes / attachement points)
7.fabric porosity (F111 only) [the most representative point of general wear is the US LE] - (you need a porosimeter or a very good knowledge of F111 wear while sucking through it)
8.fabric strength in both axis (you need a bettsometer)
9.holes or damage on the fabrics : very easy if you have a little breeze, just inflate the canopy holding it by the cell opening and watch inside / outside
C.Lines:
1.general state
2.state & stitching of each junction/cascade and ends (fingertrapped loops)
3.symmetry
4.trimming (measure under 5kg or what the manufacturer states)
5.brake lines (they generally have to be changed before the other ones)
6.if needed : line breaking strength (central A and B are the most stressed so break one of these and compare the value with the rated strength when new)
Risers are considered part of the rig. There's no absolute truth about limit values for porosity and strength tests, or acceptable deformation margins for the trimming.
It's up to you to determine your own security margins or to find a trustable rigger.
For a given variation of a given parameter, the behaviour can change differently between two different canopies.
I've seen mojo with will 800+ jumps still totally safe to jump even if loosing some flare. And other canopies with around 100-200 jumps totally worn out or snivelling because of poor care, water landings, lines deformation or other factors. And some brand new canopies opening like shit for unknown reasons!
**US LE = UpperSkin LeadingEdge (actually it's the front half part of the US)
(This post was edited by Lucifer on Jun 2, 2012, 3:15 AM)
|
|
|
|
|
|
|
|
